Errors and warnings are displayed by the following ways:

– Operator call errors are indicated by the Alarm LED lit in orange, and the error and its solution are displayed on the LCD.
– Messages during printing from a computer are displayed on the MP driver Status Monitor.
– Error codes are printed in the “operator call/service call error record” area in EEPROM information print.

Buttons valid when an operator call error occurs:

– ON button: To turn the machine off and on again.
– OK button: To clear and recover from an error. In some operator call errors, the error will automatically be cleared when the cause of the error is eliminated, and pressing the OK button may not be necessary.
– Stop button: To cancel the job at error occurrence, and to clear the error.

Operator Call Error (Alarm LED Lit In Orange)

Error	Error code	7-segment LCD	Solution
No paper in the rear tray.	[1000]	E02	Set the paper in the rear tray, and press the OK button.
Paper jam.	[1300]	E03	Remove the jammed paper, and press the OK button.
Paper output tray open.	[1251]	E03	There may be an obstacle in front of the machine. Remove it, if any, and press the OK button.
Ink cartridge not installed, or not properly installed.	[1401]	E05	Install the ink cartridge properly. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge temperature sensor error.	[1403]	E05	Re-set the ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Non-supported ink cartridge is installed.	[1485]	E05	A non-supported ink cartridge is installed. Install the supported ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge in a wrong position.	[1486]	E07	Install the ink cartridge in the correct position. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Multiple ink cartridges of the same color installed.	[1487]	E07	Confirm that each ink cartridge is installed in the correct position. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge hardware error	[1682]	E15	Re-set the ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
Ink cartridge not recognized.	[1684]	E14	A non-supported ink cartridge is installed. Install the supported ink cartridge.
The remaining ink amount unknown.	[1686]	E13	Replace the ink cartridge. Printing with an empty ink tank can damage the machine. To continue printing without replacing the ink cartridge, press the Stop/Reset button for 5 sec. or longer. (After the operation, it is recorded in the machine EEPROM that the function to detect the remaining ink amount was disabled.)
Ink cartridge not completely installed.	[1687]	E04	Re-set the ink cartridge. If the error is not cleared, the ink cartridge may be defective. Replace the ink cartridge.
No ink.	[1688]	E16	Replace the ink cartridge. Printing with an empty ink tank can damage the machine. To continue printing without replacing the ink cartridge, press the Stop/Reset button for 5 sec. or longer. (After the operation, it is recorded in the machine EEPROM that the function to detect the remaining ink amount was disabled.)
Warning: The ink absorber becomes almost full.	[1700]	E08	Replace the ink absorber, and reset the ink absorber counter. Pressing the Stop/Reset button will exit the error, and enable printing without replacing the ink absorber. However, when the ink absorber becomes full, no further printing can be performed unless the applicable ink absorber is replaced.

Service Call Error (Cyclic Blinking in Orange (Alarm LED) and Green (ON LED)

Cycles of blinking in orange and green	Error	Error code	7-seg. LCD	Conditions	Solution (Replacement of listed parts, which are likely to be faulty)
2 times	Carriage error	[5100]	P02	An error occurred in the carriage encoder signal.	1) Confirm that no foreign material is in the area where the carriage moves. 2) Clean the timing slit film. If it cannot be cleaned, replace it. 3) Replace the following items (listed in the order of likeliness to be faulty): – Carriage unit – Logic board
3 times	Line feed error	[6000]	P03	An error occurred in the LF encoder signal.	1) Perform the following for the timing slit disk film: – Clean it. – Re-attach it, if peeled off. – Replace it, if it cannot be cleaned, or if it is deformed or damaged. 2) Replace the following items (listed in the order of likeliness to be faulty): – Logic board – Drive unit
5 times	ASF cam sensor error	[5700]	P05	This error takes place when feeding paper from the rear tray after an error occurred in the rear tray cam sensor.	1) Confirm that no foreign material is around the drive gear on the side of the drive unit. 2) Replace the following items (listed in the order of likeliness to be faulty): – Drive unit – Logic board
6 times	Internal temperature error	[5400]	P06	The internal temperature is not normal.	Replace the logic board.
7 times	Ink absorber full	Japan: [5B00] Others: [5B01]	P07	The ink absorber becomes full.	Replace the ink absorber (ink absorber kit), and reset the ink absorber counter.
8 times	Print head temperature rise error	[5200]	P08	The print head temperature exceeded the specified value.	Replace the following items (listed in the order of likeliness to be faulty): – Ink cartridge – Logic board
9 times	EEPROM error	[6800] [6801]	P09	A problem occurred in reading from or writing to the EEPROM.	Replace the logic board.
10 times	VH monitor error	[B200]	P10	The print head voltage is abnormal.	Replace the following items: – Ink cartridge – Logic board
20 times	Other hardware error	[6500]	P20	An unidentified error or a network error occurred.	Replace the following item (listed in the order of likeliness to be faulty): – Logic board – WLAN board
22 times	Scanner error	[5011]	P22	The scanner unit is faulty.	Replace the following items (listed in the order of likeliness to be faulty): – Scanner unit – Logic board
23 time	Scanner motor error	[5012]	P22	The scanner motor is faulty.	Replace the following items (listed in the order of likeliness to be faulty): – Scanner unit – Logic board

Other Error

7-segment LCD	Cause	Solution
E20	The wireless LAN setting was attempted while other settings were being performed.	Wait until the settings being performed were completed, then try the wireless LAN setting.
E23	In WPS wireless LAN setting, multiple access points were detected.	Wait for a while, and perform the setting again.
E24	In WPS wireless LAN setting, an error occurred.	Confirm the access point, and perform the setting again.
E50	The machine failed in scanning the print head alignment sheet.	Press the Stop/Reset button to clear the error, perform the following, then try the print head alignment again: – Confirm that the sheet is placed in the correct orientation. – Clean the platen glass, if it is smeared. – Confirm that A4 plain paper is used. – Print the nozzle check pattern to confirm that all the ink is ejected properly.